|
Dryers
While we
attempt to maintain accuracy, we strongly suggest you contact Acme to determine
if the item(s) you see are still available for sale. We will try to update
monthly, but if you don't see what you are looking for, please contact us. We
may already have what you need, or we can do a global search and find it for
you.
| A097462 |
3.0 meter (118-inch) sheet width gas-fired Lanbein Engelbracht Compac air flotation dryer suitable for drying coated paper or coated board. Overall dimensions 3.05 meters (120 inches) long x 3.426 meters (135 inches) wide. Effective length of dryer 2.8 meters (110.2 inches). Includes 13 air flotation nozzles 3.14 meters (123.6 inches) long x 213 mm (8.4 inches wide). Insulation is 120 mm (4.7 inches) thick. Total weight 5,000 kg (11,000 pounds). Specific evaporation rate 37 kg/m2/hr. Operating temperature 250°C. Total heat requirement for continuous operation at designed temperature - 384 kW. Total heat requirement for fuel system supply - 550 kW. Includes 16,600 m3/hr. recirculation air fan with 18.5 kW motor; 6,000 m3/hr. exhaust air fan with 5.5 kW motor; 1,550 m3/hr. cooling air fan with 1.5 kW motor. Voltage for motors: 415 VAC 3-phase 50 Hz. Voltage for controls 110 VAC 50 Hz. |
| H095272 |
Used 3 meter deckle IR
dryers made by Compact Apollo with moisture profile control frame , 304
stainless steel fitted with 19 energy transmission units. Compact Power control cabinet containing 10 zones to
provide 150 mm wide zone profile control computer driven. Air filter
assembly and connecting air hoses. Spares and controls. |
| H093650 |
Used Thermo Electron thru
dryer. 30' to 40" deckle
width. Natural gas.
400 deg. F maximum temperature.
200 to 660 FPM speed range. Has
(12) 2' dia. teflon covered textile type dryer cans.
18" W x 20" L x 23" H.
2.0 MM BTU's /hr. |
| H092946 |
Used Air-Tec six zone
oven with a belt width of 54" chain center.
Single pass. Heated by
natural gas. Electrics are 3
phase, 60 cycle, 440 volt. Dryer
is 150' long (conveyor length is 160').
Maximum temperature is 600 deg. F.
Clearance above the conveyor can be varied from 4" to 8".
Each zone is 25' long. 22,500
CFM air volume per zone. Fans,
drives, temperature controls, air distribution nozzles, ductwork,
lubrication system, structural steel, and balancing dampers |
| H092524 |
One (1) Used Drying
Cylinder. 40"(1.0m) Dia
x 151"(3.83m) Face. 1" Wall Thickeners. Manuf. by Walmsley 1960's. |
| A097758 |
Used 48” dia. X 80” face,
75 psi coded Moore & White cast iron dryers with gears and sleeved
journals.
 |
| A097757 |
Used Sandy Hill 48" X 93"
cast iron dryer cans, 75 psi, live spherical roller bearings, stickle
cascade system |
| A097759 |
Used dryer section with
22 Beloit 48" x 93-1/2" face cast iron dryers, code stamped for 75 psi with
framing, gears, (bottom nylon, top steel), anti-friction bearings, top and
bottom felted. |
| A097760 |
Used dryer section with
12 Beloit 48" x 93-1/2" face cast iron dryers, code stamped for 75 psi with
framing, gears, (bottom nylon, top steel), anti-friction bearings, top and
bottom felted. |
| A097764 |
Used Valmet dryers, 48"
dia x 94" face, 75 psi, ASME coded, concave, 121.50" overall Journal, end to
end, 11-1/4" journal length t.s., 7" journal dia. t.s., 12-1/4" Journal
length d.s., 8-3/4" journal dia. d.s., sleeve bearings
 |
| A097766 |
Used 48" diameter x 94"
(with 3" rope ring) Sandy Hill dryer cans code stamped for 150 psi. Includes
frames, gears, and bearings. |
| A097765 |
Used Sandy Hill Dryers,
48" dia x 94" face, 75 psi, ASME coded, concave, 121.50" overall Journal,
end to end, 11-1/4" journal length t.s., 7" journal dia. t.s., 12-1/4"
Journal length d.s., 8-3/4" journal dia. d.s., sleeve bearings
 |
| H094712 |
One (1) used Pusey &
Jones 48" diameter x 112" face.
Rated 40 PSI non code. Includes
rope rings, sleeved bearings with gears. |
| A097970 |
Used 48" dia. X 130" GL&V
dryer can, ASME code for 150 psi @450 deg. F. New 2002. |
| A097971 |
Used 48" dia. X 130"
Beloit dryer can, ASME code for 150 psi @450 deg. F. New 2002. |
| A098049 |
Used Voith 1250 mm (49")
diameter x 3100 mm (122") dryer cans, 3 bar pressure, tested at 5 bar.
Includes open gear, steam joints and syphons |
| H095067 |
(54) used drying
cylinders, 1250 mm dia. X 3600 mm face with framing. 2.5 bar pressure,
with doctors, guide rolls, tension rolls, drive,
framework, stairs, platforms and railing. |
| A097902 |
Used Voith 1500 mm (59")
diameter x 3100 mm (122") fac dryer cans. 3 bar working pressure and tested
to 5 bar in 2004. Includes open gear, rotary steam joint, syphon. |
| A097500 |
Used 60" diameter x 180-1/4" face Valley Iron Works dryer cans. ASME code stamped for 125 psi. Babbit bearings. |
| A097909 |
Used Beloit dryer cans
60" diameter x 234" face and 212" trim, stamped for 75 psi. No bearings. |
| H092802 |
Used 2000 mm diameter x
2,700 mm face Voith drying cylinders, 3 bar.
 |
| A097443 |
One (1) used 118" dia. x 141" face (3mx3.6m) Hoesch-Düren yankee drying cylinder. Pressure rating at: 3 bars (tested at 6) new in 1970. The cylinder was never grinded and includes frames and is available immediately. Unit was dismantled end of 1998. |
| A097444 |
One (1) used 118" dia. X 141" face (3mx3.6m) Over MeccanicaYankee drying cylinder. Pressure rating at: pressure: 5 kg/cm2 with test certificate by the Ispesl Hydrotest at 7,5 kg/cm2. The Yankee dryer is made of the following: shell fabricated of special alloyed cast iron for Yankee dryers at a very fine grain externally ground to standard surface finish; heads made of high strength cast iron, with manhole fitted with steel cover plate; bolted journals on the head, made of high strength cast iron, which are internally extended and bolted to the central shaft and the rear side journal is extended and prepared to receive the hollow shaft drive gear unit while the front side journal is machined to receive the steam inlet and condensate outlet joint; condensate removal system consisting of rotating syphons, with stainless steel dipper-pipes including all of the necessary inner support brackets and piping for condensate discharge are supplied. these being, the Yankee dryer bearings and housings, etc.; the Yankee cylinder bearings are of the heavy duty double row, self-aligning roller type with clearance for thermal expansion, bearing housings of high strength cast iron of rugged construction are designed for connection to centralized oil lubrication system. |
| A097814 |
Used Over Meccanica
Yankee dryer, 3600 mm (141") diameter x 2500 mm (98.4") face. 3 bar working
pressure |
| H096109 |
Used yankee dryer
cylinder. 3600 mm diameter x
3500 mm face width. Bearing
center distance is 3920 mm. Total
width is 5500 mm. 3.5 bar
operating pressure. 45 mm
shell wall thickness. |
| A097572 |
Used Beloit Yankee dryer,
18' diameter x 204" face The dryer has surface rust but no major pitting. It
was built in 1975 by Newport News Shipbuilding for Beloit, and has a
non-ribbed internal shell surface. It is an ASME code vessel rated for 120
PSIG @ 400 Deg. F. Original shell thickness was 2.625". It has been ground
several times. It is now about 2.125" - 2.375" shell thickness range. It was
designed for operation at 3,000 FPM. |
|