| H096464 |
Used model CPF 1000 s5
Andritz 1 meter belt press, stainless steel contacts. Manufactured 1979
and used on municipal sludge. Can be used on paper, feed, and chemical
industries. Includes many spare parts. |
| A097416 |
Used 1 meter wide Voith model 1000 SB1 twin wire belt press. 83 tpd with inlet consistency of 6% and 22-25% outlet consistency (groundwood pulp 40C, ca 25 SR). Wire is 1.2 meters wide. Full specs available. |
| A097416 |
Used 1 meter wide Voith model 1000 SB1 twin wire belt press. 83 tpd with inlet consistency of 6% and 22-25% outlet consistency (groundwood pulp 40C, ca 25 SR). Wire is 1.2 meters wide. Full specs available. |
| A097382 |
Used Carter 1.5 meter belt press. Model 15/30. Type 10.91577. Has 4 main drive rolls, 13 in dia rubber coated. Driven by approx 2 hp motor. Feed roll driven by approx 1 hp. Rubber coated rolls are 4 main rolls with balance of rubber coated roll. |
| A096847 |
Used 1.6 meter Andritz
twin wire pulp press, 316 stainless steel construction. Designed to
produce 160 – 180 ADSTPD (10% a.d.) on 80% chemical and 20% TMP/SGW of
350 CSF at 100 deg.F. Includes headbox and controls. |
| A096846 |
Used 1.6 meter Andritz
twin wire pulp press, 316 stainless steel construction. Designed to
produce 180 – 210 ADSTPD (10% a.d.) on 80% chemical and 20% TMP/SGW of
400-450 CSF at 100 deg.F. Includes headbox and controls. |
| A097383 |
Used 1.6 meter, 63" wide stainless steel belt press made by EKOSEP.Used for sludge.
 |
| A097097 |
Used 1.6 meter working width Enso type ESPI 16 N# twin wire beslt press, new 1986 and used about 10 years. Wires run 5-40 m/min. Main morot 45 kW, 1500 rpm. 200 bar maximum hydraulic pressure. |
| A097383 |
Used 1.6 meter, 63" wide stainless steel belt press made by EKOSEP.Used for sludge.
 |
| A097097 |
Used 1.6 meter working
width Enso type ESPI 16 N# twin wire beslt press, new 1986 and used about
10 years. Wires run 5-40 m/min. Main morot 45 kW, 1500 rpm. 200 bar
maximum hydraulic pressure. |
| H096073 |
Used 2200mm wide Andritz
belt press model CPF 2/1 SMXP. Mild steel frame, rubber covered rollers,
galvanized bottom tray. Main drive is via electric motor through a gearbox
to a chain drive. No belts fitted but a spare belt is available. Primary
dewatering screw fitted above press, cylindrical nylon screen with
stainless steel screw feeder and galvanized housing, discharging onto
belt.
|
| H093121 |
Used Andritz model SEM
2000 K sludge dewatering belt press, belt width 2100mm, 5 kw motor drive.
Includes scraper knife. Floor
space required 4.7m x 3.6m, height 3.0m. |
| A097451 |
Used 2 meter Enso-Gutzeit twin wire belt press,2400 mm wire width, type ESPI 20N3, with a capacity of 25-35 tpd (90% substance) on sludge and 250 tpd of pulp 4% in and 35% outlet consistencies. Speed is 0-9 meters per minute. Inlet consistency is 1-5% and outlet consistency is 25-42%. |
| A098218 |
Used Arus Andritz 2.2
meter belt press, model CPF2.2 SMX-S7. Includes control panel, spare belts
and more. Photos available.
 |
| A097908 |
Used Andritz type
CPF-2200, 2.2 meter (91" wire width) sludge press with and Andritz RST-8-2
rotary screen thickner (42 TPD), new 1981, with showers and water bars at 39
gpm at 120 psi. With control panel and 18" discharge conveyor.
 |
|
A098312 |
Used Unison model 620
belt press 2.5M wide belt, stainless steel construction. 41.1square meter
filtration area. Specs available. |
| H094686 |
Used EIMCO 2.2 belt
press, stainless steel contact parts, cloth belt.
Belt width 79". 3
hp varispeed 2.2:1 ratio compression zone drive. 1 hp varispeed 57.1:1 ratio gravity drainage zone.
3/4 hp hydraulic belt tensiening.
Includes control panel. |
| H095832 |
Used Envirex 2 meter wide
dewatering belt press. T316
stainless steel product containment components.
Hydraulically operated Racine hydraulic pump drives belt through
shaft mounted 50 to 1 ratio gear reducer w/hydraulic WSI motor model RSA
s/n.018088,7.5 hp 230-460 volt TEFC. Motor and pump mounted on approx.20
gal. Tank, also services belt tensioning pistons, and belt guidance
tracking components. Doctor blade discharge.
Spray wash belt cleaning. Heavy
duty steel beam frame. Stainless
steel belt washing housing. Foam
rubber coated steel rolls with Rexnord bearings.
Mfg. order #H-116263. Nominal
rated capacity 1500#/hour. Has elec. Control panel. |
| H093823 |
Used 79" ER-WE-PA
belt press designed to run 5 - 25 feet per minute. With 7 hp drive. |
| H094530 |
Used 82" Komline-Sanderson
belt press designed to run 6 - 30 feet per minute. With 3 hp drive. |
| H096609 |
Used 2 meter Komline
Sanderson model GM2d belt filter press last used on sludge. 229.6 square feet total dewatering area.
304 s/s and carbon steel construction. |
| H092634 |
Used Parkson 2 meter
"Magnum" high pressure continuous belt press. Model MP80, new
1983. Last used on coal
slurry. Stainless steel
screen roll, others are rubber covered steel.
Hydraulic belt tensioning. 5
hp varispeed drive. 150
gallon flocculent mix tank. Mfg. Serial #82502643-20jc. |
| H096228 |
Used 3.5 meter wide
Andritz model CPF 3.5 S7 twin wire belt press. Working width 3500 mm; wire
width 2,600 mm; length of bottom wire 24,600 mm; length of top wire 24,600
mm; speed 8 - 40 feet per minute. Has two 20 hp drive motors. Headbox is
304 s/s with a stainless
steel distributor screw, 43 table
rolls. Previously used on 24-30 tpd, 30% inlet coal refuse with 98% solids
capture and 25-30% moisture. Also used on soil reclamation and can be
modified for pulp.
 |
