|
H092461 |
USED APPROX. 43" WIDE BECK SHEETER WITH STAND.
RAZOR BLADE DESIGN TYPE OF SHEETER. S/N 2319. (3) 4 POSITION LIGHT
WEIGHT BACKSTAND GOOD FOR APPROX. 24" DIA. ROLLS. ADJUSTABLE SHEET
LENGTH, BELT TAKEOFF. |
|
A097619 |
Used 1300 mm (51") wide Lamb Pasaban (Spain) Cutter
KD-1350 sheeter previously sheeting board at 150 m/min maximum. Maximum
sheet length is 1450 mm(57"); minimum sheet length is 400 mm (15.7");
maximum sheet width is 1300 mm; stack heigth is 1500 mm (59"); voltage 475
V/60 Hz. New 1995.
 |
|
A097604 |
Used 1320 mm (52") trim Clark-Aiken Model DSP1065
sheeter, 49 MTPD at 237 M/Min with belt driven 20 HP 380/220 V 50 Hz
motor. Sheeter includes: decurler unit with new decurling bar; 211 mm
rubber top squeeze roll; 268 mm steel bottom squeeze roll; 426 mm fly
knife roll with knife; bottom knife; expansion pulley unit; sheet length
adjusting gears; paper roll transfer rail; overlapping unit; layboy;
jogger; counter; unwind stand with drum brake and elevating unit and
pneumatic chucking unit; pneumatic turning device; paper sheet transfer
platform; electical equipment; pneumatic controller, etc.
 |
|
A098181 |
Used Lamb Grays Harbor Sheeter 64 x 54 (1979)
with 4 roll unwind and decurler (3 and 6 core chucks, two units also
handle 12 cores), Layboy scissor lift table/motorized trolley for roll
loading (pit mounted for floor level handling, or can be floor mounted
with loading table), Automatic tension control, Automatic stacking table
500 feet per minute speed. Scrap handling blower handles up to 8 trim on
both sides plus dust removal system, rooftop cyclone unit with blowpipe.
Also available separately is an American Baler Company model 302972R,
horizontal open end auto-tie baler (1994 mfg. date) with automatic top
feed, 29w x 42h x 72 length bales (produces approx. 1,500# bales
depending on type of paper), with Acto-Tier wire system. |
|
A098089 |
Used 1400 mm (55") trim Masson Scott simplex 600 SR
sheeter with 5 shaftless unwind stands with air brakes and tension
control. 3 slitters. Sheet length 400 - 1500 mm. Grammage 40 - 220 gsm.
Maximum speed 120 mpm. Felco short head room 2 ton crane. |
|
A097599 |
Used 1397 mm (55") trim Hamlet Model M28 sheeter, 40
MTPD actual capacity at 198 M/Min maximum speed, 20 HP 380/220 V, 50 Hz
motor. Sheeter includes: decurler unit with new decurling bar; 265 mm
rubber top squeeze roll; 333 mm steel bottom squeeze roll; 400 mm fly
knife roll with knife; bottom knife; expansion pulley unit; sheet length
adjusting gears; paper roll transfer rail; overlapping unit; layboy;
jogger; counter; unwind stand with drum brake and elevating unit and
pneumatic chucking unit; pneumatic turning device; paper sheet transfer
platform; electical equipment; pneumatic controller, etc.
 |
|
A097607 |
Used 1448 mm (57") trim Hamlet sheeter, 46 MTPD
actual capacity, 238 M/Min maximum speed, belt driven by 20 HP 380/220 V
50 Hz motor. Sheeter includes: decurler wunit with new decurling bar; 262
mm ruber top squeeze roll; 338 mm steel bottom squeeeze roll; fly knife
roll with knife; bottom knife; expansion pulley unit; sheet length
adjusting gears; paper roll transfer rail; overlapping unit; layboy;
jogger; counter; unwind stand with drum brake and elevating unit and
pneumatic chucking unit; pneumatic turning device; paper sheet transfer
platform, etc.
 |
|
A098193 |
) used 55" Strachan Henshaw Model 1400 DK Rotary
Knife Sheeter. Serial # 3A238. Equipped with one single position 40" O.D.
shafted unwind stand. 16" Diameter brake. 3" Shaft edge guide. Cut-off
range from 15" (400mm) to 59" (1500mm). Knife loading 600 GSM. 51" Pile
height including pallet. 3,300 Lbs maximum pile weight. 1000 FPM (305
m/min). (3) Shear knives. Includes platform and guarding. |
| A098245 |
One used Pemco-SHM 1450 HS single rotary sheeter new in 2005. 57" wide
machine with 2 shaftless unwind positions for 60" diameter rolls, self
loading, tracks in the floor bring the rolls to the unwind stand arms.
Slitting and equipment for delivering 3 piles. Overlapper and piler. Two
motor AC Vector drive system for speeds to 984 FPM, cut off range of 11.6"
to 59", 47" pile height, 4400 # Max. pile weight. Also has a digital
slitter position readout. Tidland Class II slitters. There is very little
running time on this machine. |
|
A097606 |
Used 1448 mm (57") trim Hamlet sheeter, 45 MTPD
actual capacity, 218 M/Min maximum speed, belt driven by 20 HP 380/220 V
50 Hz motor. Sheeter includes: decurler wunit with new decurling bar; 272
mm ruber top squeeze roll; 338 mm steel bottom squeeeze roll; fly knife
roll with knife; bottom knife; expansion pulley unit; sheet length
adjusting gears; paper roll transfer rail; overlapping unit; layboy;
jogger; counter; unwind stand with drum brake and elevating unit and
pneumatic chucking unit; pneumatic turning device; paper sheet transfer
platform, etc.
 |
|
A097601 |
Used 1448 mm (57") trim Hamlet Model M28 sheeter, 47
MTPD actual capacity, 240 M/Min maximum speed, belt driven by 20 HP
380/220 V 50 Hz motor. Sheeter includes: decurler wunit with new decurling
bar; 273 mm ruber top squeeze roll; 334 mm steel bottom squeeeze roll; fly
knife roll with knife; bottom knife; expansion pulley unit; sheet length
adjusting gears; paper roll transfer rail; overlapping unit; layboy;
jogger; counter; unwind stand with drum brake and elevating unit and
pneumatic chucking unit; pneumatic turning device; paper sheet transfer
platform, etc.
 |
|
A097600 |
Used 1448 mm (57") trim Hamlet Model M28 sheeter, 47
MTPD actual capacity, 240 M/Min maximum speed, belt driven by 20 HP
380/220 V 50 Hz motor. Sheeter includes: decurler wunit with new decurling
bar; 265 mm ruber top squeeze roll; 335 mm steel bottom squeeeze roll; fly
knife roll with knife; bottom knife; expansion pulley unit; sheet length
adjusting gears; paper roll transfer rail; overlapping unit; layboy;
jogger; counter; unwind stand with drum brake and elevating unit and
pneumatic chucking unit; pneumatic turning device; paper sheet transfer
platform, etc.
 |
|
A097605 |
Used 1448 mm (57") trim Soythworth machine Co. (USA)
Model SIDRH sheeter, 72 MTPD actual capacity at 228 M/Min maximum speed,
with 20 HP, 380/220 V, 50 Hz. Sheeter includes: decurler wunit with new
decurling bar; 253 mm ruber top squeeze roll; 400 mm steel bottom squeeeze
roll; fly knife roll with knife; bottom knife; expansion pulley unit;
sheet length adjusting gears; paper roll transfer rail; overlapping unit;
layboy; jogger; counter; unwind stand with drum brake and elevating unit
and pneumatic chucking unit; pneumatic turning device; paper sheet
transfer platform, etc.
 |
|
A097596 |
Used 1448 mm (57") trim Soythworth machine Co. (USA)
Model MDS-56 sheeter, 70 MTPD actual capacity at 270 M/Min maximum speed,
with 20 HP, 380/220 V, 50 Hz. Sheeter includes: decurler wunit with new
decurling bar; 253 mm ruber top squeeze roll; 335 mm steel bottom squeeeze
roll; fly knife roll with knife; bottom knife; expansion pulley unit;
sheet length adjusting gears; paper roll transfer rail; overlapping unit;
layboy; jogger; counter; unwind stand with drum brake and elevating unit
and pneumatic chucking unit; pneumatic turning device; paper sheet
transfer platform, etc.
 |
| A098236 |
Used Moore and White R-75 Sheeter with a shaftless self loading unwind for
60" wide rolls, 72" Max OD, 12" cores. Includes decurling, slitting, two
motor drive, overlapper and piler. New in 1987. |
|
A097580 |
Used 60" web Lambs Gray M114 sheeter with a
shaftless Langston backstand type JP double roll operation. Max web 96" x
60" diameter. 7000# max roll wieght.
 |
|
A097608 |
Used 1626 mm (64") trim Simflex sheeter, 46 MTPD at
218 M/Min, belt driven by 20 HP 380/220 V 50 Hz motor. Sheeter includes:
decurler unit with new decurling bar; 272 mm rubber top squeeze roll; 320
mm steel bottom squeeze roll; 430 mm fly knife roll with knife; bottom
knife fixture with knife; expansion pulley unit; sheet length adjusting
gears; layboy unit; vibrating jogger; counter; unwind stack device, etc.
 |
|
A098179 |
Used 1600 mm (63") Pasaban Symcrom Sheet Cutter with
2 shaftless unwinds, automatic brakes, reject system, and automatic pallet
change. Previous typical speed was 200 MPM. |
|
A098101 |
Rebuilt 1600 mm (63") wide sheet cutter with dead
knife system, overlap system, 8 shafted unwinds, hydraulic table for
pallets. Sheet length from 400 mm to 1600 mm. Maximum speed is 200
meters/minute. 1500 mm pallet height. Newly replaced electrics. Unused
since rebuilt.
 |
|
A097594 |
Used 1600 mm (63") trim Hamlet sheeter capable of 73
MTPD at 250 MPM driven by 20 HP 50 HZ motor. Sheeter includes: decurler
unit with new decurling bar; 266 mm rubber top squeeze roll; 333 mm steel
bottom squeeze roll; 390 mm fly knife roll with knife; bottom knife
fixture with knife; expansion pulley unit; sheet length adjusting gears;
layboy unit; vibrating jogger; counter; unwind stack device, etc.
 |
| A098238 |
Used Jagenberg Folio Sheeter, model Synchro 21, having a cutoff range of
21.625" to 78.75" and equipped with a 72" turret unwind stand (two
positions, auto splice, auto roll change, 12" diameter coreshafts, up to
6000lbs.), slitting capability, two (2) lay boys, web aligner upgrade,
Rockwell PIC electronics with computer touch screen (new in 2008). Maximum
mechanical speed: 820FPM (250MPM). |
|
A097870 |
64" Jagenberg Synchrofly Model AS116. Age 1987. 350m
per minute. Uncoated paper / coated paper. Sheet length 420-1800mm. Knife
load maximum 600gsm. 4 sets of shear cut knives. Minimum slit width 16".
(2) 6 reel unwind stands with lift tables. Air braking. 60" diameter rolls
of material. (3) 6" cores. (5) individual decurl units. Roll detector.
Layboy. Type Palettomat. Pile height 1650mm. DC drive motor. Separate
motors for draw & cross cutting section. Auto reject. Jagenberg gear box
for synchrofly cutoff. Dust suction overlapping section with Vaccu-Stop-System.
Nonstop operation during pile change. 3 ream markers. Has been creating 3
piles. Typical operating speed 600 FPM. Precision sheeter. Can be seen in
operation. |
|
A097597 |
Used 1626 mm (64") trim Clark-Aiken sheeter, 77 MTPD
acturl capacity at 256 M/Min maximum speed, 25 HP 380/220 V 50 Hz motor.
Sheeter includes: decurler unit with new decurling bar; 265 mm rubber top
squeeze roll; 322 mm steel bottom squeeze roll; 430 mm fly knife roll with
knife; bottom knife; expansion pulley unit; sheet length adjusting gears;
paper roll transfer rail; overlapping unit; layboy; jogger; counter;
unwind stand with drum brake and elevating unit and pneumatic chucking
unit; pneumatic turning device; paper sheet transfer platform; electical
equipment; pneumatic controller, etc.
 |
|
A097869 |
Used 61" Jagenberg Model AS 28 Syncrofly type
sheeter. Age 1977. This is a precision sheeter equipped for non-stop
operation at the delivery end. It has been sheeting paper board from .008
through .040 thicknesses. Equipped with four Jagenberg shaftless floor
pickup unwinds; these unwinds are equipped with 12" core chucks and will
accept 72" maximum roll dia. Unwinds are controlled automatically by a
combination of load cell and dancer roll tension control. Two unwinds can
be utilized while two others are re-loaded with new rolls of paper to
minimize downtime. The brakes on these unwinds are air-operated &
air-cooled. Following the unwind position, the webs proceed over a Fife
steering roll system for web alignment. The web can then proceed over a
series of decurlers; there are a total of three decurlers and these are
roll type. The sheeter is equipped with shear cut slitting; 3 sets of
knives are available. The cutoff range for the sheeter is 21.7" minimum to
79.5" maximum. Following the sheeting head, cut sheets proceed through an
overlap system to a layboy section. This layboy can accumulate up to three
different stacks at one time and is equipped with jogging. Accuracy on
cutoff on a 1 meter sheet length (40") is reported as +/- 1mm. Typical
operating speed depends upon sheet length. On a 24" sheet length, speed is
approx. 280 FPM; on 2 meters (80"), approx. 590 FPM. Optimum speed is
achieved on cutoff lengths of 34" to 63" and at these lengths, speed is
825 FPM. Machine is equipped with a Fortress inline metal detector. The
cutoff length is changed by a combination of PIV & gearbox. The layboy is
equipped with a set of "forks"; these allow continuous operation while a
finished skid of sheets is being removed and an empty skid replaced. These
forks hold the accumulating sheets while the change is made. This machine
has been sheeting chipboard and coated board products. This machine is
going to be released in March 2005. Machine is in operation. Owner reports
the mechanical condition of the machine to be excellent. In production &
is kept flawless. The owner will load the machine out onto truck for an
additional $50,000. Includes reject system. Montalvo automatic tension
control systems on unwind. |
|
A098021 |
Used Beilomatik model P 885/140, year 1995, max
speed 400m/min, max width 1.65m, folio cutter cutting SRA2, SRA1, B2 and
B1, 5 backstands with side loading conveyors and hydraulic roll lift.
Pneumatic brakes with tension control, edge guide, 5 slitters, reject
gate, vacuum overlap section, ream counter and taber, twin accept layboys
with auto changeover stack. |
|
A097586 |
Used 64" Clark Aiken FPGS (DS) Sheeter. Dual Martin
Shaftless Floor Pick-Up Backstand with 60" O.D. Roll Capacity. S/N RS 624
& 1936. Clark Aiken Matic dancer system mdl 200180 with Dynaweb pneumatic
tension control system mdl EP 200A. Overhead idler roll system with
General Web edge guide. Decurler station variable angle. 24" O.D. Knife
Cylinder. Shear Slitting. Overlap, Layboy & reject station. 60" height
capacity chain pilier with side and corner vibrators. Reliance max pac VS
drive system with 30 HP motor. Clark Aiken Differential w/link belt
PIV(motorized). Sheet Length Determined by Individual Gears & PIV
Adjustment. Red Lion digital readouts. +/ - 1/32 Tolerance. |
|
A097602 |
Used 1651 mm (65") trim Hamlet sheeter, 50 MTPD
actual capacity at 243 M/Min maximum speed, 20 HP motor, 380/220V 50 Hz.
Sheeter includes: decurler unit with new decurling bar; 256 mm rubber top
squeeze roll; 337 mm steel bottom squeeze roll; 400 mm fly knife roll with
knife; bottom knife; expansion pulley unit; sheet length adjusting gears;
paper roll transfer rail; overlapping unit; layboy; jogger; counter unit;
unwind stand with drum brake and elevating unit and pneumatic chucking
unit; pneumatic turning device; paper sheet transfer platform; pneumatic
controller; etc.
 |
| A098237 |
Used Jagenberg Folio Sheeter, model Synchro 21, having a cutoff range of
21.625" to 78.75" and equipped with a 72" turret unwind stand (two
positions, auto splice, auto roll change, 12" diameter coreshafts, up to
6000lbs.), slitting capability, two (2) lay boys, web aligner upgrade,
Rockwell PIC electronics with computer touch screen (new in 2008). Maximum
mechanical speed: 820FPM (250MPM). |
|
A097595 |
Used 1651 mm (65") trim Hamlet model 28 sheeter, 69
MTPD actual capacity at 265 M/Min maximum speed, 20 HP motor, 380/220V 50
Hz. Sheeter includes: decurler unit with new decurling bar; 255 mm rubber
top squeeze roll; 336 mm steel bottom squeeze roll; 400 mm fly knife roll
with knife; bottom knife; expansion pulley unit; sheet length adjusting
gears; paper roll transfer rail; overlapping unit; layboy; jogger; counter
unit; unwind stand with drum brake and elevating unit and pneumatic
chucking unit; pneumatic turning device; paper sheet transfer platform;
pneumatic controller; etc.
 |
|
A098125 |
Used Jagenberg Synchro AS 116 sheeter. 60 300 gsm
on coated and uncoated paper. Includes 6 roll backstands. 1700 mm maximum
and 670 minimum roll width. Maximum working width 1650 mm. 2970 mm cut
width and 420 1600 mm cut length. 350 mpm maximum speed. Produced 80
tpd. |
|
A097583 |
Used 68" wide Hamblet sheeter fixed bed knife rotary
top knife machine complete with a roll stand and stacker. The sheeter has
a 69" wide rubber covered feed roll, a motor driven decurler, a stationary
bed knife with a rotary top, an all mechanical reeve type sheet length
system. All sheet length controls are operator initiated without a feed
back system. It appears that all the fiber gears are on hand to cover the
full range of sheet lengths. The roll stand has motor driven roll elevator
and chuck side frames and a pneumatic brake. The chucks are designed for
12" cores. All roll stand controls are operator initiated.
 |
|
A09815 |
Used 1780 mm (70) Masson Scott Sheeter able to make
sheets 430mm minimum and 2160 mm maximum length 3 up with 4 slitters and
single rotary knife. 1800 mm diameter x 2200 mm unwinder width. Maximum
machine speed is 180 MPM. Includes unwinder load cell, IP controller for
web tensioning, decurler bar, stacking table and stack vibrator jogger
plate. |
|
A097603 |
Used 1855 mm (73") trim Hamlet sheeter, 43 MTPD
actual capacity at 237 M/Min maximum speed, 20 HP 380/220 V, 50 Hz motor.
Sheeter includes: decurler unit with new decurling bar; 338 mm rubber top
squeeze roll; 312 mm steel bottom squeeze roll; 393 mm fly knife roll with
knife; bottom knife; expansion pulley unit; sheet length adjusting gears;
paper roll transfer rail; overlapping unit; layboy; jogger; counter;
unwind stand with drum brake and elevating unit and pneumatic chucking
unit; pneumatic turning device; paper sheet transfer platform; electical
equipment; pneumatic controller, etc.
 |
|
A097598 |
Used 1855 mm (73") trim Hamlet Model MDS sheeter, 62
MTPD actual capacity at 220 M/Min maximum speed, 20 HP 380/220 V, 50 Hz
motor. Sheeter includes: decurler unit with new decurling bar; 265 mm
rubber top squeeze roll; 335 mm steel bottom squeeze roll; 400 mm fly
knife roll with knife; bottom knife; expansion pulley unit; sheet length
adjusting gears; paper roll transfer rail; overlapping unit; layboy;
jogger; counter; unwind stand with drum brake and elevating unit and
pneumatic chucking unit; pneumatic turning device; paper sheet transfer
platform; electical equipment; pneumatic controller, etc.
 |
|
A097445 |
Used 1900 mm (75") trim Jagenberg Synchro Folio
Sheeter RQ-GL with double synchro sheeting drums (Simplex). Minimum sheet
size 420 x 580 mm (16.5" x 22.75"); max. sheet size 1900 x 1600 mm (75" x
63"); max speed 200 MPM (700 FPM). Speed is quality and size dependent.
Maximum knife load is 500 g. 8 + 8 shafless unwinds on rail system; 2 high
pile deliveries plus 1 waste gate delivery. Shear slitting section with 4
knife sets. Spreading roller before slitting section. 132 TPD (24 hours)
maximu production, with an average of 66 tpd. |
|
A098090 |
Used 2387 mm (94") Masson Scott LQ L2 duplex sheeter
with 6 slitters, 4 stand unwind with cone type backbars and air brakes.
Sheet length 400 - 1820 mm. Grammage 40 - 220 gsm. Max. speed 60 mpm.
Felco shorth head room 3 ton crane. |
|
A098223 |
Used Jagenberg duplex sheeter, width is 2400 mm to
1600 mm , length is 1600 mm to 500 mm. With 3 roll unwind. |
|
A098224 |
Used 2400 mm Jagenberg rype RQS / GI simplex synchro
sheeter. Used on coated board 220 - 700 GSM at 150 maximum speed. Length
from 600 - 1800 mm. High pile 1500 mm. Reject gate. 2 shaftless unwinder
adjustable with disc brake. 30 HP, 1750 rpm 220 / 380 V, 50 cycles. |
|
A097807 |
Used 95" wide Marquip Model III automatic on-line
duplex rotary sheeter with layboy. New 1992. Machine is capable of
sheeting up to 4 sheets across at 2 different lengths. Minimum length is
17" and maximum is 74". Previously ran 8" - 18" wide diverted into 12"
deep storage bins. 72" max. stack height (6000 lbs). Designed for
paperboard 57 - 140 lbs/1000 sq. ft. Unit has integral chop out shear, 2
Tidland slitter sections, a defect detector and dump gate as well as 2
self piling layboys. Sheet cutoff variance is typically less than 1/32".
All functions are automated and controlled by user interface console. |
|
A098225 |
Used Marquip 2450 mm duplex synchro Model III L
sheeter.250 - 300 maximum MPM on coated board 200 - 550 GSM.100 TPD.
Marquip double unwinder, seet stacker and spares. |
|
H095977 |
USED MODEL M-1 LAMBS GRAY HARBOR 108"
SHEETER/LAYBOY, PRODUCED PAPERBOARD HEADERS AND MARKET PULP BALE WRAPPERS
AND PAPERBOARD SHEETING, 235 - 455 GSM. 600-1200 FEET PER MINUTE RANGE,
1000 FPM TYPICAL. INFEED ROLL HANDLING CONSISTS OF 1 ROLL LIFT,(2) 8" TO
14" UNWIND STANDS. SINGLE KNIFE CUTTER. LAYBOY WITH AUTOMATIC SHEET
REJECT, FRONT FEED TAG INSERTER AND POWERED DISCHARGE TABLE. 460 VOLT, 3
PHASE PRIMARY ELECTRICAL REQUIREMENTS. |
|
A098113 |
Used 117" Pasaban Model KSD-3100 duplex rotary
sheeter. Built in 1992. Working width is 117". Maximum speed is 1100 FPM.
Maximum unwind width is 118". Maximum unwind diameter is 78". Maximum core
diameter is 18". Maximum sheet length is 63". Minimum sheet length is 20".
Maximum sheet width is 117". Maximum pile height is 70". Machine has been
placed in storage as of 1997. Will sheet up to 800g/m2. |
|
A097788 |
Used 3040 mm (120") Jagenberg model DQSM/GL
synchronized duplex sheeter. 2000 mm maximum dutting length; 700 gsm
maximum grammage; design cutting length is 500 - 2400 mm. Type 33 unwind
stand, 2000 mm max diameter. 1200 mm pallet height and 120 meters/minute
maximum speed. |
|
A097074 |
Used Lamb pulp sheet cutter, 5000 mm web width to
produce 1000 tpd with 2 web layers. Cutter with 4 unwind stands. DC drive.
Includes a turning device for jumbo rolls, a dividing conveyor on a cart.
Some spare parts. |
