Slitters

H092564	USED 12" WIDE ARROW MODEL 300 SLITTER/REWINDER. HAS 18" O.D. MAXIMUM UNWIND, 12" O.D. REWIND. SCORE AND RAZOR SLITTING CAPABILITIES ON 1" AND 3" CORES.
H093192	One (1) used 40" Schiavi slitter-rewinder with 42" O.D unwind capacity. Razor slitting. Speed rated at 1400 FPM maximum 1640 FPM. 3 Phase motor 380/220 volts 50/60 Hz. Manufactured in mid 1970. Out of service.
A098138	46" Kidder CWN single shaft center rewind slitter rewinder. Easy to operate. 40" dia. unwind & rewind. Shear cut slitting. (1) 3" air unwind shaft. (1) 3" air rewind shaft. Manual skew adjustment. Manual edge guiding of unwinding roll approx. 6". Montalvo 12" air-cooled, air-operated brake. Cleveland Kidder automatic tension control automatically controls braking of unwinding roll. Hydraulic roll loading & unloading on both unwind & rewind. Designed for one man operation; 1 operator can run 2 machines. Durant 2-stage electric counter stops at pre-determined count or footage. Approx. 30 female knives & 5 male knives. Minimum slit width 2". Electrics: 230/460 volt, 60 cycle, 3 phase, 15 HP Emerson DC motor with Spectrum solid-state controller. Taper tension control. Mechanical speeds 3000 FPM. Typical operating speed 2000 FPM. Good for slitting & rewinding one time carbon paper, carbonless paper, register bond, tabulated card stock, gift wrapping paper, tag & label stock, kraft paper, foil, laminated foil, coated paper, photographic films, laminated products, newsprint, tissue & toweling, nonwovens, tube & core stock, cellophane, P/S laminations & many other laminations. Can be used for non-extensible products & heavyweight plastics. Often used as a roll doctor machine for paper which has been printed. True center rewind machine with single shaft, the only driven part. Range of materials typically run on machine; 5.5 lb. carbon tissue to 220 lb. tag stock. Most recently slitting coated papers & carbonless paper. Designed so that as rewinding roll increases in diameter the slitter carriage is moved towards the rear of the machine while constantly maintaining the shortest possible web travel from the cutters to the rewinding roll preventing interweaving of the slit stock as it is rewound. Automatic minimum gap rewinding. Equipped with rider roll, which can be used to remove entrapped air contribute to roll hardness. 2 speed transmission. As machine is designed without winding drums it is possible to slit & rewind coated & treated materials at high speeds without damage & waste. Motorized slitting carriage control with electric eyes allows machine to be operated with minimum gap control so a fixed distance can automatically be maintained between rewinding roll of material & pressing roll. Carbonless paper & other coated materials need this feature to assure no scratches on the material.
A098139	47" Kidder Model CW single shaft center rewind slitter rewinder. 50" dia. unwind. 50" dia. rewind. Shear cut slitting. (1) 3" air shaft on unwind. (1) 3" air shaft on rewind. Manual edge guiding. Manual skew adjustment. 20" Montalvo air-cooled, air-operated brake. CMC automatic tension control system. Automatic tension control on brake automatically controls unwinding brake as diameter decreases. Maintains constant tension. Hydraulic mill roll loading & unloading on unwind & rewind. No hoists are needed for loading or unloading machine. Designed for one-man operation. One operator can run two machines. Approx. 45 female knives. 9 male knives. Minimum slit width 2". Reliance 40 HP DC variable speed drive motor. Controller for drive motor is Cleveland Machine Controls. 460 volt, 3 phase, 60 cycle. Taper tension control. Mechanical speed 3000 FPM. Kidder CW is good for slitting & rewinding one-time carbon paper, carbonless paper, register bond, tabulated card stock, gift wrapping paper, tag & label stock, kraft paper, foil, laminated foil, coated paper, photographic films, laminated products, newsprint, tissue & toweling, nonwovens, tube & core stock, cellophane, pressure-sensitive laminations & many other non-extensible products. Typically used for non-extensible products & heavyweight plastics. Is a true center rewind with single shaft, the only drive part. Most recently slitting coated papers. As rewinding roll increases in diameter, slitter carriage is moved towards rear of machine while constantly maintaining shortest possible web travel from shear cutters to rewinding roll, thus preventing interweaving of slit stock as it is rewound. Tachometer generator drive control is wired to speed indicator & drive motor. Current acts as an automatic field control to maintain constant motor torque horsepower & predetermined web speed regardless of constantly changing diameter of mill & rewinding roll. Due to automatic feedback, many different products can be slit & rewound. 50" wide idler rolls.
H096351	One (1) used Cameron 62" wide capacity Slitter/Rewinder System consisting of: Cameron Model 354 "Duplex" Type Slitter, reverse wind feature, two (2) core wind up reels with hydraulic positioning cylinder, tensioning rolls, slitter bar with adjustable blade holders, fife edge guide system with floor standing power unit, variable speed drive, trim pick up tubes, foot pedal and lever controls, floor standing control panel with analog and digital gauges, 1000 to 1200 FPM Speeds, 24" diameter meximum roll capacity, Serial No. P28915: Cameron Model "LSM" Unwind Stand, Adjustable Core Holders, Pneumatic Disc Brake Tensioning and Cooling Blower, 1000# maximum roll capacity, overhead track mounted toll cellophane, tailed windup roll, overhead track mounted "electro-lift" 2000# capacity cellophane roll, cable hoist with (2) positioning lift clamp bars, complete with motors and SCR
H093440	One(1)Used Dusenbery 840 KSS, Unwind Width: 1600mm+, Rewind Width: 1600mm+,Reel Diameter: 960mm, It Is 2 drum surface winder. The Slitting Width is Infinite To The Full Width Of The Reel. It Has Banana Roller To Take Up Any Bagginess In The Paper, It Has A Web Guide.
A097763	Used 2700 mm (100”) Perrini E 1010 fully automatic 2 ply slitter rewinder, new 1988. Unit has vertical rider roll; 600 mpm speed. Max width of jumbo roll is 2650 mm (104”) and max roll diameter is 2000 mm (79”). 2 shaftless unwinding stands. Minimum roll width is 100 mm (3.9”). Mandrin diameter is 62.5 mm. Finished roll diameter is 120 – 400 mm. All functions controlled by PLC unit. 50 kW power load. Compressed air consumption is 0.6 Nm3/min. Has 27 knives. Still in operation as of 6/04.
A097361	Used 2800 mm (110") trim Jagenberg 43-15 slitter rewinder with 1200 mm unwind, 1525 mm rewind at 600 MPM. Used on 18 - 45 gsm tissue, 45 - 90 gsm writing. Can run u to 240 gsm. 6 knives. Unwinding stand.